| /* $FreeBSD$ */ |
| /** @file |
| EFI PCI I/O Protocol provides the basic Memory, I/O, PCI configuration, |
| and DMA interfaces that a driver uses to access its PCI controller. |
| |
| Copyright (c) 2006 - 2010, Intel Corporation. All rights reserved.<BR> |
| This program and the accompanying materials |
| are licensed and made available under the terms and conditions of the BSD License |
| which accompanies this distribution. The full text of the license may be found at |
| http://opensource.org/licenses/bsd-license.php |
| |
| THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, |
| WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED. |
| |
| **/ |
| |
| #ifndef __PCI_IO_H__ |
| #define __PCI_IO_H__ |
| |
| #define EFI_PCI_ROOT_IO_GUID \ |
| { 0x2F707EBB, 0x4A1A, 0x11d4, { 0x9A, 0x38, 0x00, 0x90, 0x27, 0x3F, 0xC1, 0x4D }} |
| |
| /// |
| /// Global ID for the PCI I/O Protocol |
| /// |
| #define EFI_PCI_IO_PROTOCOL_GUID \ |
| { 0x4cf5b200, 0x68b8, 0x4ca5, {0x9e, 0xec, 0xb2, 0x3e, 0x3f, 0x50, 0x2, 0x9a} } |
| |
| typedef struct _EFI_PCI_IO_PROTOCOL EFI_PCI_IO_PROTOCOL; |
| |
| /// |
| /// ******************************************************* |
| /// EFI_PCI_IO_PROTOCOL_WIDTH |
| /// ******************************************************* |
| /// |
| typedef enum { |
| EfiPciIoWidthUint8 = 0, |
| EfiPciIoWidthUint16, |
| EfiPciIoWidthUint32, |
| EfiPciIoWidthUint64, |
| EfiPciIoWidthFifoUint8, |
| EfiPciIoWidthFifoUint16, |
| EfiPciIoWidthFifoUint32, |
| EfiPciIoWidthFifoUint64, |
| EfiPciIoWidthFillUint8, |
| EfiPciIoWidthFillUint16, |
| EfiPciIoWidthFillUint32, |
| EfiPciIoWidthFillUint64, |
| EfiPciIoWidthMaximum |
| } EFI_PCI_IO_PROTOCOL_WIDTH; |
| |
| // |
| // Complete PCI address generater |
| // |
| #define EFI_PCI_IO_PASS_THROUGH_BAR 0xff ///< Special BAR that passes a memory or I/O cycle through unchanged |
| #define EFI_PCI_IO_ATTRIBUTE_MASK 0x077f ///< All the following I/O and Memory cycles |
| #define EFI_PCI_IO_ATTRIBUTE_ISA_MOTHERBOARD_IO 0x0001 ///< I/O cycles 0x0000-0x00FF (10 bit decode) |
| #define EFI_PCI_IO_ATTRIBUTE_ISA_IO 0x0002 ///< I/O cycles 0x0100-0x03FF or greater (10 bit decode) |
| #define EFI_PCI_IO_ATTRIBUTE_VGA_PALETTE_IO 0x0004 ///< I/O cycles 0x3C6, 0x3C8, 0x3C9 (10 bit decode) |
| #define EFI_PCI_IO_ATTRIBUTE_VGA_MEMORY 0x0008 ///< MEM cycles 0xA0000-0xBFFFF (24 bit decode) |
| #define EFI_PCI_IO_ATTRIBUTE_VGA_IO 0x0010 ///< I/O cycles 0x3B0-0x3BB and 0x3C0-0x3DF (10 bit decode) |
| #define EFI_PCI_IO_ATTRIBUTE_IDE_PRIMARY_IO 0x0020 ///< I/O cycles 0x1F0-0x1F7, 0x3F6, 0x3F7 (10 bit decode) |
| #define EFI_PCI_IO_ATTRIBUTE_IDE_SECONDARY_IO 0x0040 ///< I/O cycles 0x170-0x177, 0x376, 0x377 (10 bit decode) |
| #define EFI_PCI_IO_ATTRIBUTE_MEMORY_WRITE_COMBINE 0x0080 ///< Map a memory range so writes are combined |
| #define EFI_PCI_IO_ATTRIBUTE_IO 0x0100 ///< Enable the I/O decode bit in the PCI Config Header |
| #define EFI_PCI_IO_ATTRIBUTE_MEMORY 0x0200 ///< Enable the Memory decode bit in the PCI Config Header |
| #define EFI_PCI_IO_ATTRIBUTE_BUS_MASTER 0x0400 ///< Enable the DMA bit in the PCI Config Header |
| #define EFI_PCI_IO_ATTRIBUTE_MEMORY_CACHED 0x0800 ///< Map a memory range so all r/w accesses are cached |
| #define EFI_PCI_IO_ATTRIBUTE_MEMORY_DISABLE 0x1000 ///< Disable a memory range |
| #define EFI_PCI_IO_ATTRIBUTE_EMBEDDED_DEVICE 0x2000 ///< Clear for an add-in PCI Device |
| #define EFI_PCI_IO_ATTRIBUTE_EMBEDDED_ROM 0x4000 ///< Clear for a physical PCI Option ROM accessed through ROM BAR |
| #define EFI_PCI_IO_ATTRIBUTE_DUAL_ADDRESS_CYCLE 0x8000 ///< Clear for PCI controllers that can not genrate a DAC |
| #define EFI_PCI_IO_ATTRIBUTE_ISA_IO_16 0x10000 ///< I/O cycles 0x0100-0x03FF or greater (16 bit decode) |
| #define EFI_PCI_IO_ATTRIBUTE_VGA_PALETTE_IO_16 0x20000 ///< I/O cycles 0x3C6, 0x3C8, 0x3C9 (16 bit decode) |
| #define EFI_PCI_IO_ATTRIBUTE_VGA_IO_16 0x40000 ///< I/O cycles 0x3B0-0x3BB and 0x3C0-0x3DF (16 bit decode) |
| |
| #define EFI_PCI_DEVICE_ENABLE (EFI_PCI_IO_ATTRIBUTE_IO | EFI_PCI_IO_ATTRIBUTE_MEMORY | EFI_PCI_IO_ATTRIBUTE_BUS_MASTER) |
| #define EFI_VGA_DEVICE_ENABLE (EFI_PCI_IO_ATTRIBUTE_VGA_PALETTE_IO | EFI_PCI_IO_ATTRIBUTE_VGA_MEMORY | EFI_PCI_IO_ATTRIBUTE_VGA_IO | EFI_PCI_IO_ATTRIBUTE_IO) |
| |
| /// |
| /// ******************************************************* |
| /// EFI_PCI_IO_PROTOCOL_OPERATION |
| /// ******************************************************* |
| /// |
| typedef enum { |
| /// |
| /// A read operation from system memory by a bus master. |
| /// |
| EfiPciIoOperationBusMasterRead, |
| /// |
| /// A write operation from system memory by a bus master. |
| /// |
| EfiPciIoOperationBusMasterWrite, |
| /// |
| /// Provides both read and write access to system memory by both the processor and a |
| /// bus master. The buffer is coherent from both the processor's and the bus master's point of view. |
| /// |
| EfiPciIoOperationBusMasterCommonBuffer, |
| EfiPciIoOperationMaximum |
| } EFI_PCI_IO_PROTOCOL_OPERATION; |
| |
| /// |
| /// ******************************************************* |
| /// EFI_PCI_IO_PROTOCOL_ATTRIBUTE_OPERATION |
| /// ******************************************************* |
| /// |
| typedef enum { |
| /// |
| /// Retrieve the PCI controller's current attributes, and return them in Result. |
| /// |
| EfiPciIoAttributeOperationGet, |
| /// |
| /// Set the PCI controller's current attributes to Attributes. |
| /// |
| EfiPciIoAttributeOperationSet, |
| /// |
| /// Enable the attributes specified by the bits that are set in Attributes for this PCI controller. |
| /// |
| EfiPciIoAttributeOperationEnable, |
| /// |
| /// Disable the attributes specified by the bits that are set in Attributes for this PCI controller. |
| /// |
| EfiPciIoAttributeOperationDisable, |
| /// |
| /// Retrieve the PCI controller's supported attributes, and return them in Result. |
| /// |
| EfiPciIoAttributeOperationSupported, |
| EfiPciIoAttributeOperationMaximum |
| } EFI_PCI_IO_PROTOCOL_ATTRIBUTE_OPERATION; |
| |
| /** |
| Reads from the memory space of a PCI controller. Returns either when the polling exit criteria is |
| satisfied or after a defined duration. |
| |
| @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. |
| @param Width Signifies the width of the memory or I/O operations. |
| @param BarIndex The BAR index of the standard PCI Configuration header to use as the |
| base address for the memory operation to perform. |
| @param Offset The offset within the selected BAR to start the memory operation. |
| @param Mask Mask used for the polling criteria. |
| @param Value The comparison value used for the polling exit criteria. |
| @param Delay The number of 100 ns units to poll. |
| @param Result Pointer to the last value read from the memory location. |
| |
| @retval EFI_SUCCESS The last data returned from the access matched the poll exit criteria. |
| @retval EFI_UNSUPPORTED BarIndex not valid for this PCI controller. |
| @retval EFI_UNSUPPORTED Offset is not valid for the BarIndex of this PCI controller. |
| @retval EFI_TIMEOUT Delay expired before a match occurred. |
| @retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources. |
| @retval EFI_INVALID_PARAMETER One or more parameters are invalid. |
| |
| **/ |
| typedef |
| EFI_STATUS |
| (EFIAPI *EFI_PCI_IO_PROTOCOL_POLL_IO_MEM)( |
| IN EFI_PCI_IO_PROTOCOL *This, |
| IN EFI_PCI_IO_PROTOCOL_WIDTH Width, |
| IN UINT8 BarIndex, |
| IN UINT64 Offset, |
| IN UINT64 Mask, |
| IN UINT64 Value, |
| IN UINT64 Delay, |
| OUT UINT64 *Result |
| ); |
| |
| /** |
| Enable a PCI driver to access PCI controller registers in the PCI memory or I/O space. |
| |
| @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. |
| @param Width Signifies the width of the memory or I/O operations. |
| @param BarIndex The BAR index of the standard PCI Configuration header to use as the |
| base address for the memory or I/O operation to perform. |
| @param Offset The offset within the selected BAR to start the memory or I/O operation. |
| @param Count The number of memory or I/O operations to perform. |
| @param Buffer For read operations, the destination buffer to store the results. For write |
| operations, the source buffer to write data from. |
| |
| @retval EFI_SUCCESS The data was read from or written to the PCI controller. |
| @retval EFI_UNSUPPORTED BarIndex not valid for this PCI controller. |
| @retval EFI_UNSUPPORTED The address range specified by Offset, Width, and Count is not |
| valid for the PCI BAR specified by BarIndex. |
| @retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources. |
| @retval EFI_INVALID_PARAMETER One or more parameters are invalid. |
| |
| **/ |
| typedef |
| EFI_STATUS |
| (EFIAPI *EFI_PCI_IO_PROTOCOL_IO_MEM)( |
| IN EFI_PCI_IO_PROTOCOL *This, |
| IN EFI_PCI_IO_PROTOCOL_WIDTH Width, |
| IN UINT8 BarIndex, |
| IN UINT64 Offset, |
| IN UINTN Count, |
| IN OUT VOID *Buffer |
| ); |
| |
| typedef struct { |
| /// |
| /// Read PCI controller registers in the PCI memory or I/O space. |
| /// |
| EFI_PCI_IO_PROTOCOL_IO_MEM Read; |
| /// |
| /// Write PCI controller registers in the PCI memory or I/O space. |
| /// |
| EFI_PCI_IO_PROTOCOL_IO_MEM Write; |
| } EFI_PCI_IO_PROTOCOL_ACCESS; |
| |
| /** |
| Enable a PCI driver to access PCI controller registers in PCI configuration space. |
| |
| @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. |
| @param Width Signifies the width of the memory operations. |
| @param Offset The offset within the PCI configuration space for the PCI controller. |
| @param Count The number of PCI configuration operations to perform. |
| @param Buffer For read operations, the destination buffer to store the results. For write |
| operations, the source buffer to write data from. |
| |
| |
| @retval EFI_SUCCESS The data was read from or written to the PCI controller. |
| @retval EFI_UNSUPPORTED The address range specified by Offset, Width, and Count is not |
| valid for the PCI configuration header of the PCI controller. |
| @retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources. |
| @retval EFI_INVALID_PARAMETER Buffer is NULL or Width is invalid. |
| |
| **/ |
| typedef |
| EFI_STATUS |
| (EFIAPI *EFI_PCI_IO_PROTOCOL_CONFIG)( |
| IN EFI_PCI_IO_PROTOCOL *This, |
| IN EFI_PCI_IO_PROTOCOL_WIDTH Width, |
| IN UINT32 Offset, |
| IN UINTN Count, |
| IN OUT VOID *Buffer |
| ); |
| |
| typedef struct { |
| /// |
| /// Read PCI controller registers in PCI configuration space. |
| /// |
| EFI_PCI_IO_PROTOCOL_CONFIG Read; |
| /// |
| /// Write PCI controller registers in PCI configuration space. |
| /// |
| EFI_PCI_IO_PROTOCOL_CONFIG Write; |
| } EFI_PCI_IO_PROTOCOL_CONFIG_ACCESS; |
| |
| /** |
| Enables a PCI driver to copy one region of PCI memory space to another region of PCI |
| memory space. |
| |
| @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. |
| @param Width Signifies the width of the memory operations. |
| @param DestBarIndex The BAR index in the standard PCI Configuration header to use as the |
| base address for the memory operation to perform. |
| @param DestOffset The destination offset within the BAR specified by DestBarIndex to |
| start the memory writes for the copy operation. |
| @param SrcBarIndex The BAR index in the standard PCI Configuration header to use as the |
| base address for the memory operation to perform. |
| @param SrcOffset The source offset within the BAR specified by SrcBarIndex to start |
| the memory reads for the copy operation. |
| @param Count The number of memory operations to perform. Bytes moved is Width |
| size * Count, starting at DestOffset and SrcOffset. |
| |
| @retval EFI_SUCCESS The data was copied from one memory region to another memory region. |
| @retval EFI_UNSUPPORTED DestBarIndex not valid for this PCI controller. |
| @retval EFI_UNSUPPORTED SrcBarIndex not valid for this PCI controller. |
| @retval EFI_UNSUPPORTED The address range specified by DestOffset, Width, and Count |
| is not valid for the PCI BAR specified by DestBarIndex. |
| @retval EFI_UNSUPPORTED The address range specified by SrcOffset, Width, and Count is |
| not valid for the PCI BAR specified by SrcBarIndex. |
| @retval EFI_INVALID_PARAMETER Width is invalid. |
| @retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources. |
| |
| **/ |
| typedef |
| EFI_STATUS |
| (EFIAPI *EFI_PCI_IO_PROTOCOL_COPY_MEM)( |
| IN EFI_PCI_IO_PROTOCOL *This, |
| IN EFI_PCI_IO_PROTOCOL_WIDTH Width, |
| IN UINT8 DestBarIndex, |
| IN UINT64 DestOffset, |
| IN UINT8 SrcBarIndex, |
| IN UINT64 SrcOffset, |
| IN UINTN Count |
| ); |
| |
| /** |
| Provides the PCI controller-specific addresses needed to access system memory. |
| |
| @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. |
| @param Operation Indicates if the bus master is going to read or write to system memory. |
| @param HostAddress The system memory address to map to the PCI controller. |
| @param NumberOfBytes On input the number of bytes to map. On output the number of bytes |
| that were mapped. |
| @param DeviceAddress The resulting map address for the bus master PCI controller to use to |
| access the hosts HostAddress. |
| @param Mapping A resulting value to pass to Unmap(). |
| |
| @retval EFI_SUCCESS The range was mapped for the returned NumberOfBytes. |
| @retval EFI_UNSUPPORTED The HostAddress cannot be mapped as a common buffer. |
| @retval EFI_INVALID_PARAMETER One or more parameters are invalid. |
| @retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources. |
| @retval EFI_DEVICE_ERROR The system hardware could not map the requested address. |
| |
| **/ |
| typedef |
| EFI_STATUS |
| (EFIAPI *EFI_PCI_IO_PROTOCOL_MAP)( |
| IN EFI_PCI_IO_PROTOCOL *This, |
| IN EFI_PCI_IO_PROTOCOL_OPERATION Operation, |
| IN VOID *HostAddress, |
| IN OUT UINTN *NumberOfBytes, |
| OUT EFI_PHYSICAL_ADDRESS *DeviceAddress, |
| OUT VOID **Mapping |
| ); |
| |
| /** |
| Completes the Map() operation and releases any corresponding resources. |
| |
| @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. |
| @param Mapping The mapping value returned from Map(). |
| |
| @retval EFI_SUCCESS The range was unmapped. |
| @retval EFI_DEVICE_ERROR The data was not committed to the target system memory. |
| |
| **/ |
| typedef |
| EFI_STATUS |
| (EFIAPI *EFI_PCI_IO_PROTOCOL_UNMAP)( |
| IN EFI_PCI_IO_PROTOCOL *This, |
| IN VOID *Mapping |
| ); |
| |
| /** |
| Allocates pages that are suitable for an EfiPciIoOperationBusMasterCommonBuffer |
| mapping. |
| |
| @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. |
| @param Type This parameter is not used and must be ignored. |
| @param MemoryType The type of memory to allocate, EfiBootServicesData or |
| EfiRuntimeServicesData. |
| @param Pages The number of pages to allocate. |
| @param HostAddress A pointer to store the base system memory address of the |
| allocated range. |
| @param Attributes The requested bit mask of attributes for the allocated range. |
| |
| @retval EFI_SUCCESS The requested memory pages were allocated. |
| @retval EFI_UNSUPPORTED Attributes is unsupported. The only legal attribute bits are |
| MEMORY_WRITE_COMBINE and MEMORY_CACHED. |
| @retval EFI_INVALID_PARAMETER One or more parameters are invalid. |
| @retval EFI_OUT_OF_RESOURCES The memory pages could not be allocated. |
| |
| **/ |
| typedef |
| EFI_STATUS |
| (EFIAPI *EFI_PCI_IO_PROTOCOL_ALLOCATE_BUFFER)( |
| IN EFI_PCI_IO_PROTOCOL *This, |
| IN EFI_ALLOCATE_TYPE Type, |
| IN EFI_MEMORY_TYPE MemoryType, |
| IN UINTN Pages, |
| OUT VOID **HostAddress, |
| IN UINT64 Attributes |
| ); |
| |
| /** |
| Frees memory that was allocated with AllocateBuffer(). |
| |
| @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. |
| @param Pages The number of pages to free. |
| @param HostAddress The base system memory address of the allocated range. |
| |
| @retval EFI_SUCCESS The requested memory pages were freed. |
| @retval EFI_INVALID_PARAMETER The memory range specified by HostAddress and Pages |
| was not allocated with AllocateBuffer(). |
| |
| **/ |
| typedef |
| EFI_STATUS |
| (EFIAPI *EFI_PCI_IO_PROTOCOL_FREE_BUFFER)( |
| IN EFI_PCI_IO_PROTOCOL *This, |
| IN UINTN Pages, |
| IN VOID *HostAddress |
| ); |
| |
| /** |
| Flushes all PCI posted write transactions from a PCI host bridge to system memory. |
| |
| @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. |
| |
| @retval EFI_SUCCESS The PCI posted write transactions were flushed from the PCI host |
| bridge to system memory. |
| @retval EFI_DEVICE_ERROR The PCI posted write transactions were not flushed from the PCI |
| host bridge due to a hardware error. |
| |
| **/ |
| typedef |
| EFI_STATUS |
| (EFIAPI *EFI_PCI_IO_PROTOCOL_FLUSH)( |
| IN EFI_PCI_IO_PROTOCOL *This |
| ); |
| |
| /** |
| Retrieves this PCI controller's current PCI bus number, device number, and function number. |
| |
| @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. |
| @param SegmentNumber The PCI controller's current PCI segment number. |
| @param BusNumber The PCI controller's current PCI bus number. |
| @param DeviceNumber The PCI controller's current PCI device number. |
| @param FunctionNumber The PCI controller's current PCI function number. |
| |
| @retval EFI_SUCCESS The PCI controller location was returned. |
| @retval EFI_INVALID_PARAMETER One or more parameters are invalid. |
| |
| **/ |
| typedef |
| EFI_STATUS |
| (EFIAPI *EFI_PCI_IO_PROTOCOL_GET_LOCATION)( |
| IN EFI_PCI_IO_PROTOCOL *This, |
| OUT UINTN *SegmentNumber, |
| OUT UINTN *BusNumber, |
| OUT UINTN *DeviceNumber, |
| OUT UINTN *FunctionNumber |
| ); |
| |
| /** |
| Performs an operation on the attributes that this PCI controller supports. The operations include |
| getting the set of supported attributes, retrieving the current attributes, setting the current |
| attributes, enabling attributes, and disabling attributes. |
| |
| @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. |
| @param Operation The operation to perform on the attributes for this PCI controller. |
| @param Attributes The mask of attributes that are used for Set, Enable, and Disable |
| operations. |
| @param Result A pointer to the result mask of attributes that are returned for the Get |
| and Supported operations. |
| |
| @retval EFI_SUCCESS The operation on the PCI controller's attributes was completed. |
| @retval EFI_INVALID_PARAMETER One or more parameters are invalid. |
| @retval EFI_UNSUPPORTED one or more of the bits set in |
| Attributes are not supported by this PCI controller or one of |
| its parent bridges when Operation is Set, Enable or Disable. |
| |
| **/ |
| typedef |
| EFI_STATUS |
| (EFIAPI *EFI_PCI_IO_PROTOCOL_ATTRIBUTES)( |
| IN EFI_PCI_IO_PROTOCOL *This, |
| IN EFI_PCI_IO_PROTOCOL_ATTRIBUTE_OPERATION Operation, |
| IN UINT64 Attributes, |
| OUT UINT64 *Result OPTIONAL |
| ); |
| |
| /** |
| Gets the attributes that this PCI controller supports setting on a BAR using |
| SetBarAttributes(), and retrieves the list of resource descriptors for a BAR. |
| |
| @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. |
| @param BarIndex The BAR index of the standard PCI Configuration header to use as the |
| base address for resource range. The legal range for this field is 0..5. |
| @param Supports A pointer to the mask of attributes that this PCI controller supports |
| setting for this BAR with SetBarAttributes(). |
| @param Resources A pointer to the ACPI 2.0 resource descriptors that describe the current |
| configuration of this BAR of the PCI controller. |
| |
| @retval EFI_SUCCESS If Supports is not NULL, then the attributes that the PCI |
| controller supports are returned in Supports. If Resources |
| is not NULL, then the ACPI 2.0 resource descriptors that the PCI |
| controller is currently using are returned in Resources. |
| @retval EFI_INVALID_PARAMETER Both Supports and Attributes are NULL. |
| @retval EFI_UNSUPPORTED BarIndex not valid for this PCI controller. |
| @retval EFI_OUT_OF_RESOURCES There are not enough resources available to allocate |
| Resources. |
| |
| **/ |
| typedef |
| EFI_STATUS |
| (EFIAPI *EFI_PCI_IO_PROTOCOL_GET_BAR_ATTRIBUTES)( |
| IN EFI_PCI_IO_PROTOCOL *This, |
| IN UINT8 BarIndex, |
| OUT UINT64 *Supports, OPTIONAL |
| OUT VOID **Resources OPTIONAL |
| ); |
| |
| /** |
| Sets the attributes for a range of a BAR on a PCI controller. |
| |
| @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. |
| @param Attributes The mask of attributes to set for the resource range specified by |
| BarIndex, Offset, and Length. |
| @param BarIndex The BAR index of the standard PCI Configuration header to use as the |
| base address for resource range. The legal range for this field is 0..5. |
| @param Offset A pointer to the BAR relative base address of the resource range to be |
| modified by the attributes specified by Attributes. |
| @param Length A pointer to the length of the resource range to be modified by the |
| attributes specified by Attributes. |
| |
| @retval EFI_SUCCESS The set of attributes specified by Attributes for the resource |
| range specified by BarIndex, Offset, and Length were |
| set on the PCI controller, and the actual resource range is returned |
| in Offset and Length. |
| @retval EFI_INVALID_PARAMETER Offset or Length is NULL. |
| @retval EFI_UNSUPPORTED BarIndex not valid for this PCI controller. |
| @retval EFI_OUT_OF_RESOURCES There are not enough resources to set the attributes on the |
| resource range specified by BarIndex, Offset, and |
| Length. |
| |
| **/ |
| typedef |
| EFI_STATUS |
| (EFIAPI *EFI_PCI_IO_PROTOCOL_SET_BAR_ATTRIBUTES)( |
| IN EFI_PCI_IO_PROTOCOL *This, |
| IN UINT64 Attributes, |
| IN UINT8 BarIndex, |
| IN OUT UINT64 *Offset, |
| IN OUT UINT64 *Length |
| ); |
| |
| /// |
| /// The EFI_PCI_IO_PROTOCOL provides the basic Memory, I/O, PCI configuration, |
| /// and DMA interfaces used to abstract accesses to PCI controllers. |
| /// There is one EFI_PCI_IO_PROTOCOL instance for each PCI controller on a PCI bus. |
| /// A device driver that wishes to manage a PCI controller in a system will have to |
| /// retrieve the EFI_PCI_IO_PROTOCOL instance that is associated with the PCI controller. |
| /// |
| struct _EFI_PCI_IO_PROTOCOL { |
| EFI_PCI_IO_PROTOCOL_POLL_IO_MEM PollMem; |
| EFI_PCI_IO_PROTOCOL_POLL_IO_MEM PollIo; |
| EFI_PCI_IO_PROTOCOL_ACCESS Mem; |
| EFI_PCI_IO_PROTOCOL_ACCESS Io; |
| EFI_PCI_IO_PROTOCOL_CONFIG_ACCESS Pci; |
| EFI_PCI_IO_PROTOCOL_COPY_MEM CopyMem; |
| EFI_PCI_IO_PROTOCOL_MAP Map; |
| EFI_PCI_IO_PROTOCOL_UNMAP Unmap; |
| EFI_PCI_IO_PROTOCOL_ALLOCATE_BUFFER AllocateBuffer; |
| EFI_PCI_IO_PROTOCOL_FREE_BUFFER FreeBuffer; |
| EFI_PCI_IO_PROTOCOL_FLUSH Flush; |
| EFI_PCI_IO_PROTOCOL_GET_LOCATION GetLocation; |
| EFI_PCI_IO_PROTOCOL_ATTRIBUTES Attributes; |
| EFI_PCI_IO_PROTOCOL_GET_BAR_ATTRIBUTES GetBarAttributes; |
| EFI_PCI_IO_PROTOCOL_SET_BAR_ATTRIBUTES SetBarAttributes; |
| |
| /// |
| /// The size, in bytes, of the ROM image. |
| /// |
| UINT64 RomSize; |
| |
| /// |
| /// A pointer to the in memory copy of the ROM image. The PCI Bus Driver is responsible |
| /// for allocating memory for the ROM image, and copying the contents of the ROM to memory. |
| /// The contents of this buffer are either from the PCI option ROM that can be accessed |
| /// through the ROM BAR of the PCI controller, or it is from a platform-specific location. |
| /// The Attributes() function can be used to determine from which of these two sources |
| /// the RomImage buffer was initialized. |
| /// |
| VOID *RomImage; |
| }; |
| |
| extern EFI_GUID gEfiPciIoProtocolGuid; |
| |
| #endif |